![]() I prefer to fly in Rate/Acro mode so i didn’t test Angle/Horizon modes. I’ve configured it to arm on one AUX switch and failsafe + beeper on second AUX switch. I’ve setup failsafe to drop immediately as i think it’s a safer option. I tried several different bands and channels with my cyclops FPV goggles (which has auto scanning), every time the image was crystal clear.įinally I put the housing back on, and continued to setup Betaflight, such as Reciever (ibus) + failsafes on FC, low voltage alarm (aka buzzer), RX failsafe and bind were done earlier. It’s not tilted at all, and it’s impossible to do so… as it is glued in place. Second problem I found with the VTX/Camera combo was the tilt angle. One thing I didn’t like was that in order to change VTX channel, you need to first remove the canopy, because there is no quick access to the button. It is a 25mw unit with a dipole antenna as a sting of a wasp – antenna is well placed and hopefully won’t get sucked into spinning props. While I had the canopy removed, I investigated the VTX + camera combo. As you can see the frame has additional cut out to accommodate the cables: I had to unsolder 3 cables and removed the DSM receiver and solder 3 silicon cables for the flysky receiver.Īfter that, I placed my RX in a good spot on top of the FC, and have my antenna reached out like a second “sting”. Underneath you can see the FC and stock receiver, If you own a DSM compatible TX, you don’t need to do this.įirst of all, I removed 5 phillips screws to take off the wasp’s canopy (watch out the 5 screws have different length). Initial check went fine, Gyro and Accelerometer was working as expected, also I did an ACC calibration.īecause I’m a FlySky user, i had to take the wasp apart to replace stock DSM receiver (tiny one) with a flysky receiver. Once connected the FC to computer, I found Betaflight V3.0.1 was already installed. 8 propellers of length 44mm – tri-blade, colours are black and yellowĬonnecting Flight Controller with Computer Via USB, however I encountered a small issue: the USB port location is not easy to access, and the cable didn’t fit due to the placement of the “wasp” housing – my solution was to get an USB extension cable with smaller end.1 battery (orange) 400mah 2s (came charged at 7.83V).Wasp comes in a nice package – well secured, no damage to the drone or the packaging even if the external package was damaged. Pros and cons – what works and what could be improved.First steps – what comes in the box and what was required before first take off.This article is divided into the following sections: There is also another version that support Frsky receivers. The unit we reviewed is version 1 which includes the DSM receiver. The quality of the reception has a lot to do with your transmitter and with the antennae.If you would want to use a DVR, that should be pretty straightforward because these goggles are easy to disassemble.The FuriBee Wasp is available at Gearbest (link) in one of three variants: For those who have never used a 800x480 model in the past, the Furibee VR01's 480x272 resolution is not going to matter.The reception, however, is respectable. But this is likely to matter only if you are already used to 800x480. A button on the top acts as a switch you can use to change sources.There are no batteries included. It also comes with an a/v cable with an RCA adapter and a 3.5 mm jack. Or you can use any other receiver you like. The model lets you to utilize the receiver that comes with it. The video reception is pretty good - even when there is a much RF noise in the surroundings.The two antennae are of the circularly polarized type. All parts that touch your face are padded - and so wearing them for a extended periods does not cause the slightest amount of discomfort.That said, the goggles are made from low quality plastic - so these certainly do not feel like some of the more expensive ones on the market.These FPV goggles have two RX5808 chips in a diversity configuration. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |